for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 234 linear & power amplifiers - smt hmc455lp3 / 455lp3e ingap hbt ? watt high ip3 amplifier, 1.7 - 2.5 ghz v02.0605 general description features functional diagram the hmc455lp3 & HMC455LP3E are high output ip3 gaas ingap heterojunction bipolar transistor (hbt) ? watt mmic ampli ers operating between 1.7 and 2.5 ghz. utilizing a minimum number of external components the ampli er provides 13 db of gain and +28 dbm of saturated power at 56% pae from a single +5 vdc supply voltage. the high output ip3 of +42 dbm coupled with the low vswr of 1.4:1 make the hmc455lp3 & HMC455LP3E ideal driver ampli ers for pcs/3g wireless infrastructures. a low cost, leadless 3x3 mm qfn surface mount package (lp3) houses the linear ampli er. the lp3 provides an exposed base for excellent rf and thermal performance. output ip3: +42 dbm gain: 13 db 56% pae @ +28 dbm pout +19 dbm w-cdma channel power @ -45 dbc acp 3x3 mm qfn smt package electrical speci cations, t a = +25 c, vs= +5v typical applications this ampli er is ideal for high linearity applications: ? multi-carrier systems ? gsm, gprs & edge ? cdma & wcdma ? phs parameter min. typ. max. min. typ. max. min. typ. max. units frequency range 1.7 - 1.9 1.9 - 2.2 2.2 - 2.5 ghz gain 11.5 13.5 10.5 13 9 11.5 db gain variation over temperature 0.012 0.02 0.012 0.02 0.012 0.02 db / c input return loss 13 15 10 db output return loss 10 18 15 db output power for 1db compression (p1db) 24 27 24.5 27.5 23 26 dbm saturated output power (psat) 28.5 28 27 dbm output third order intercept (ip3) 37 40 39 42 37 40 dbm noise figure 7 6 6 db supply current (icq) 150 150 150 ma
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 235 input return loss vs. temperature output return loss vs. temperature broadband gain & return loss gain vs. temperature p1db vs. temperature psat vs. temperature data shown is tuned for 1.85 - 2.2 ghz, contact hmc applications for recommended 1.7 - 1.85 ghz & 2.2 - 2.5 ghz tuning circuits. hmc455lp3 / 455lp3e ingap hbt ? watt high ip3 amplifier, 1.7 - 2.5 ghz v02.0605 -25 -20 -15 -10 -5 0 5 10 15 1 1.5 2 2.5 3 s21 s11 s22 response (db) frequency (ghz) -30 -25 -20 -15 -10 -5 0 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c return loss (db) frequency (ghz) -25 -20 -15 -10 -5 0 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c return loss (db) frequency (ghz) 20 21 22 23 24 25 26 27 28 29 30 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c p1db (dbm) frequency (ghz) 20 22 24 26 28 30 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c psat (dbm) frequency (ghz) 5 8 11 14 17 20 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c gain (db) frequency (ghz)
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 236 linear & power amplifiers - smt power compression @ 1.95 ghz output ip3 vs. temperature noise figure vs. temperature gain, power & ip3 vs. supply voltage @ 1.95 ghz reverse isolation vs. temperature power compression @ 2.15 ghz data shown is tuned for 1.85 - 2.2 ghz, contact hmc applications for recommended 1.7 - 1.85 ghz & 2.2 - 2.5 ghz tuning circuits. hmc455lp3 / 455lp3e ingap hbt ? watt high ip3 amplifier, 1.7 - 2.5 ghz v02.0605 30 32 34 36 38 40 42 44 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c ip3 (dbm) frequency (ghz) 0 10 20 30 40 50 60 -10 -5 0 5 10 15 20 pout gain pae pout (dbm), gain (db), pae (%) input power (dbm) 8 12 16 20 24 28 32 36 40 44 4.5 4.7 5 5.2 5.5 gain p1db psat ip3 gain (db), p1db (dbm), psat (dbm), ip3 (dbm) vs (v) -30 -25 -20 -15 -10 -5 0 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c isolation (db) frequency (ghz) 0 1 2 3 4 5 6 7 8 9 10 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 +25c +85c -40c noise figure (db) frequency (ghz) 0 10 20 30 40 50 60 -10 -5 0 5 10 15 20 pout gain pae pout (dbm), gain (db), pae (%) input power (dbm)
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 237 acpr vs. supply voltage @ 1.96 ghz cdma 2000, 9 channels forward acpr vs. supply voltage @ 2.14 ghz w-cdma, 64 dpch absolute maximum ratings collector bias voltage (vcc) +6.0 vdc rf input power (rfin)(vs = +5vdc) +25 dbm junction temperature 150 c continuous pdiss (t = 85 c) (derate 16 mw/c above 85 c) 1.04 w thermal resistance (junction to ground paddle) 63 c/w storage temperature -65 to +150 c operating temperature -40 to +85 c hmc455lp3 / 455lp3e ingap hbt ? watt high ip3 amplifier, 1.7 - 2.5 ghz v02.0605 -65 -60 -55 -50 -45 -40 5 7 9 11 13 15 17 19 21 acpr (dbc) channel output power (dbm) source acpr cdma2000 rev. 8 frequency: 1.96 ghz integration bw: 1.228 mhz forward link, sr1, 9 channels 5.5v 4.5v 5v -65 -60 -55 -50 -45 -40 -35 -30 5 7 9 11 13 15 17 19 21 acpr (dbc) channel output power (dbm) source acpr wcdma frequency : 2.14 ghz integration bw: 3.84 mhz 64 dpch 4.5v 5v 5.5v electrostatic sensitive device observe handling precautions application circuit recommended component values l1 8.2 nh c1 2.2 f c2, c3 3.0 pf c4 0.9 pf c5 100 pf data shown is tuned for 1.85 - 2.2 ghz, contact hmc applications for recommended 1.7 - 1.85 ghz & 2.2 - 2.5 ghz tuning circuits. tl1 tl2 tl3 tl4 impedance 50 ohm 50 ohm 50 ohm 50 ohm physical length 0.33? 0.18? 0.13? 0.04? electrical length 34 19 13.5 4 pcb material: 10 mil rogers 4350, er = 3.48
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 238 linear & power amplifiers - smt pin descriptions pin number function description interface schematic 1, 2, 4 - 9, 11 - 16 n/c this pin may be connected to rf ground. 3 rfin this pin is ac coupled. an off chip series matching capacitor is required. 10 rfout rf output and dc bias for the output stage. gnd package bottom must be connected to rf/dc ground. hmc455lp3 / 455lp3e ingap hbt ? watt high ip3 amplifier, 1.7 - 2.5 ghz v02.0605 outline drawing notes: 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters] 3. lead spacing tolerance is non-cumulative 4. pad burr length shall be 0.15mm maximum. pad burr height shall be 0.05mm maximum. 5. package warp shall not exceed 0.05mm. 6. all ground leads and ground paddle must be soldered to pcb rf ground. 7. refer to hittite application note for suggested land pattern. part number package body material lead finish msl rating package marking [3] hmc455lp3 low stress injection molded plastic sn/pb solder msl1 [1] 455 xxxx HMC455LP3E rohs-compliant low stress injection molded plastic 100% matte sn msl1 [2] 455 xxxx [1] max peak re ow temperature of 235 c [2] max peak re ow temperature of 260 c [3] 4-digit lot number xxxx package information
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 239 hmc455lp3 / 455lp3e ingap hbt ? watt high ip3 amplifier, 1.7 - 2.5 ghz v02.0605 evaluation pcb the circuit board used in the nal application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be con- nected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation board should be mounted to an appropriate heat sink. the evaluation circuit board shown is available from hittite upon request. list of materials for evaluation pcb 106058 [1] item description j1 - j2 pcb mount sma connector j3 2 mm dc header c1 2.2 f capacitor, tantalum c2, c3 3.0 pf capacitor, 0402 pkg. c4 0.9 pf capacitor, 0402 pkg. c5 100 pf capacitor, 0402 pkg. l1 8.2 nh inductor, 0402 pkg. u1 hmc455lp3 / HMC455LP3E power ampli er pcb [2] 106492 evaluation pcb, 10 mils [1] reference this number when ordering complete evalution pcb [2] circuit board material: rogers 4350, er = 3.48 pin number description 1, 2, 3 gnd 4, 5, 6 vs j3 data shown is tuned for 1.85 - 2.2 ghz, contact hmc applications for recommended 1.7 - 1.85 ghz & 2.2 - 2.5 ghz tuning circuits.
|
